Where to get ballistic gel

Our ballistic gelatin does not require special storage. Our entire ballistic gelatin process is batch controlled. Clear Ballistics does calibration on the gelatin with each batch, and we following the FBI protocol for ballistics testing developed for ballistic testing of human tissue.

All blocks in this category follow the FBI protocol for calibrating ordnance gelatin A so it can be used as ballistic gelatin. Ballistic Gel by the Pound comes in a convenient shaved form. It is sold in one pound increment which, are packaged in a bag. The Air Rifle Block is the perfect size for testing the flight and penetration of projectiles for all of your non-lethal hobby weapons, and all commercial grade air guns.

This block is the same size that the FBI and other law enforcement agencies use for terminal ballistics testing and data. Ballistic Gelatin FBI Block sized for hunters, hobbyist, semi-professional, and professional shooters, all types of law enforcement agencies. Our Bow Block is perfect for all archers. This size gives you the archer four quadrants to shoot into and gather four times the data need for your testing.

The creation of our Bow Block was to assist you the archer in choosing the correct shaft, fletching and arrowhead combination for your hunt. This block of ballistic Gelatin is meant for hunters, hobbyist, semi-professional and professional archers.

Weighing in just less than 40 LBS. With each block being independent form one another you have the option of different configurations. Half SWAT Pak Our Ballistic Gelatin Half Swat Block is perfect for terminal ballistics testing for all handguns and rifles where you penetration is less than 19 inches, with a front surface area of 96 square inches. The mixing process will take a significant amount of time, so make sure that you can comfortably mix for about twenty minutes.

Add the gelatin. Use a 1-cup measuring cup to slowly add gelatin to the water. You need to be stirring constantly to avoid clumping. Add all of the gelatin over the course of about 10 minutes, sprinkling one cup at a time. This step is much easier with two people.

One person stirs, while the other slowly adds the gelatin. After the gelatin has been added, you can swap stirring duties to give your arm a break. To improve the clarity, you can add cinnamon oil to the gelatin. You will need about 9 drops; 1 drop per gallon of water. Add the cinnamon oil about halfway through the stirring process.

Scoop off foam and bubbles. After the stirring is complete, there will be a little bit of foam on the top of the mixture. Gently scoops this out and discard. There should be no visible foam or clumps of undissolved gelatin in the final mix. Cool the gelatin. Avoid freezing it, or else the blocks will become too cloudy. Cool the gel for at least 8 hours, preferably overnight. Extract the gel. Once the gel has fully cooled, gently turn the container over onto a clean flat surface such as a kitchen counter.

Slowly guide the gel out of the container with your hands to help avoid cracking the block. Cut the gel. Use a large kitchen knife to cut the block into two halves. Cut the long way so that you are left with two narrow blocks with the dimensions 6 x 6 x Gently wrap each block completely in plastic wrap.

This will prevent evaporation, which will affect the density and integrity of the block. After wrapping the block, place a stiff piece of cardboard on each block and wrap it again. The cardboard will make transporting the block much easier. Transport the blocks in a cooler to help keep them at optimum density. Shoot the block. Place the blocks on a stable flat surface. A piece of plywood on sawhorses will work. Adjust the blocks so that you shoot into a 6 x 6 square end.

If you are firing a high-powered gun, place a cement block behind the ballistics gel to keep the force from knocking the block off of the platform. Always follow proper safety procedures when handling fierarms. Ballistics gel is typically shot from about 10 feet 3. There are three standard tests: Naked — nothing covering the block.

Lightly clothed — two t-shirts covering the block. Heavily clothed — two t-shirts and two pairs of jeans covering the block. Take photos. If you want to take photos of the results, paint the plywood that you placed the blocks on white. This will highlight the bullet fragments. You will be able to see the results best in bright sunlight.

Method 4. Assemble your materials. You will need two plastic containers 16 oz , two packets of Knox Gelatine, a measuring cup, cooking spray, and water. Pour the gelatin into one of the containers. Add both packets to one container. Slowly add the water to the gelatin. Stir the mixture with a spoon slowly to keep air bubbles from forming. Place the stirred mixture into a refrigerator for hours.

Fill a sink with hot water. Place the chilled container into the hot water for about 15 minutes to melt the set gelatin back into a liquid. If the water is not hot enough, the gelatin will not melt back down to liquid form. Heat water on a stove if necessary. Spray the other container. While the gel is melting, spray the second container with the cooking spray. Pour the melted gel into the second container.

Slowly pour the melted gel to keep air bubbles from forming under the surface. Place the gel back in fridge and let it cool for 12 hours.

Knock the gel out of the container. Once the gel has set, you can knock it out of the container. It should easily fall out in one piece, thanks to the cooking spray. Shoot the gel. Place the gel on a flat stable surface and shoot it with the airsoft or pellet gun.

Shoot from about 10 feet 3. Will the gel melt back into a liquid state after several hours, or will it stay gelled forever? After several hours out of the fridge, the gel will melt back into liquid form. Not Helpful 3 Helpful Once the gelatin has melted, can it be re-used if I remove any bullet fragments?

Not Helpful 4 Helpful Yes, it can. Remove all the bullet fragments from it first before you melt it. Not Helpful 1 Helpful To reuse it for another weapon without buying more gelatin. Just like reloading old cases. Not Helpful 9 Helpful 9. Chemically, it seems viable.

Soap shouldn't make it any less clear, either. You could try it in a smaller container first, maybe 6 in x 6 in x 6 in and 1. If you are wanting to test ballistics on this however, you shouldn't want it any thicker as it will lessen the impact of the rounds. Not Helpful 3 Helpful 5. Ballistics gel can be used by spies as building bricks for sniper hides, or to make a vest that will show them how much worse a bullet wound could have been once they've been shot.

They would have to keep in mind, though that if it gets too hot it will liquefy. In a sniper hide, this really creates a difficult cleanup while covering their tracks, so they should make sure they bring plenty of ice and a fan to cool it back down for an easier cleanup.

When used as a vest, the melt could make them appear to be nervous and blow their cover. Not Helpful 31 Helpful Not this one. It is still only gelatine, and as such, it will mold after some time. Up to a week should be fine, though. If you really need to, replace half of the water with isopropyl alcohol and glycerin in equal amounts; that should give you up to one year, under perfect conditions. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.